Owens Corning Attic Insulation Nationwide

Owens Corning Attic Insulation: The Austin Owner’s Guide

If you’ve got Owens Corning insulation in your attic and it’s no longer doing its job, we stock and install Owens Corning-compatible blown-in fiberglass, batt, and roll insulation across Austin with same-week scheduling in most cases. Installed replacement typically runs $1,800 to $4,600 depending on attic square footage, current R-value, and whether we’re topping off existing material or removing and starting fresh. Most Austin homeowners discover the problem the hard way: an upstairs bedroom that won’t cool below 80 in August, a utility bill that jumped 40% summer over summer, or a pest infestation that turned their insulation into a nesting site.

Call (325) 246-2929

A quick word on who we are: Aspen Attic Insulation Austin is an independent insulation contractor. We’re not affiliated with Owens Corning, but we carry their products because, frankly, the pink stuff performs in Texas heat when it’s installed at the right depth and density. Garrett Sloane, our owner, has been in Austin attics long enough to know exactly how the humidity and 100-degree summers punish insulation that was installed thin or has since compacted.

Which Owens Corning Models This Applies To

Owens Corning’s attic insulation lineup breaks into three families, and the compatibility details matter more than most homeowners realize. The blown-in products are AttiCat Pink Fiberglas (the expanding loose-fill system that contractors blow through the AttiCat machine) and ProPink L77 loose-fill. The batt and roll lines include EcoTouch PINK Fiberglas (available in R-19, R-30, and R-38), R-30C and R-38C High-Performance batts for cathedral ceilings, and the Thermafiber mineral wool line for fire-rated assemblies. There’s also the Propink ComfortTherm wrapped batt, which some Austin builders spec’d in the mid-2000s.

Here’s the compatibility gotcha most sites won’t tell you: blown-in AttiCat and batts don’t mix cleanly for air-sealing purposes. If your attic already has settled AttiCat at R-19 and you want to reach R-38, you can blow more AttiCat on top, but you should not lay batts over uneven blown material. The batts bridge over low spots and create air channels that defeat the whole point. We match the top-up material to what’s already there. And if your home was built before 1990 in Austin, there’s a decent chance the original insulation contains vermiculite or has degraded paper facing that needs removal before topping up.

How to know what you have: look for the pink or white fiberglass with printed facing. Owens Corning batts carry face-stapling flanges or a white or kraft paper vapor barrier with the R-value printed every few feet. Blown AttiCat looks like loose, fluffy pink or white cotton-like material. If you’re not sure, snap a photo and we’ll identify it during the estimate.

Signs Your Owens Corning Attic Insulation Is Failing

• Upstairs rooms run 8 to 12 degrees warmer than downstairs in the afternoon. This means your attic insulation has either compacted below its rated R-value or was never deep enough for Central Texas. Austin attics hit 140°F in July; the heat radiates through thin coverage by 3 p.m. every day.
• Utility bills in July and August are noticeably higher than the same months two years ago, with no change in your AC habits. Insulation doesn’t fail suddenly. It degrades in small increments and your electric bill is the first place the loss shows up.
• You can see the tops of your ceiling joists through the insulation. If insulation sits at or below joist level, you’re under-insulated. Current code in Texas recommends R-38 to R-49 for attics, and most older Austin homes were built with R-19 or less.
• There are dark, matted, or damp patches in the insulation. A roof leak, an AC condensate issue, or a bathroom vent that terminates in the attic instead of through the roof will soak fiberglass. Wet Owens Corning loses its R-value quickly and becomes a mold and pest magnet.
• You hear scratching or find pellet droppings in the attic. Rats, squirrels, and raccoons love burrowing through fiberglass batts. Tunneled, packed-down insulation performs at a fraction of its rated R-value.

Replacement Cost & What’s Included

Here’s what Austin homeowners can expect to pay, installed, for Owens Corning-compatible attic insulation in 2025:

• Top-up blown AttiCat to R-38 over existing insulation: $1,200 to $2,100 for a typical 1,200 to 1,600 square foot attic.
• Remove and replace existing insulation with AttiCat to R-38: $2,400 to $3,900, including old insulation removal, air sealing of penetrations, and disposal.
• Full removal and replacement with R-38 batts plus air sealing: $3,000 to $4,600, depending on attic access, existing moisture damage, and whether baffles need installation at the eaves.
• Add R-30 batts in a small bonus room or finished attic space: $800 to $1,400.

Where the range falls depends on three things: how much old material has to come out, how many air leaks need sealing before we insulate, and how difficult the attic access is. A cramped 3/12 pitch attic with a closet hatch costs more than a walkable attic with a pull-down stair. Every quote we give is a written price before any work starts. That’s not a selling line; it’s how we’ve operated since 2002 as part of the Threshold Group family. The price on the quote is the price on the invoice, period. And the work carries our 365-Day Done Right Promise: if the insulation settles past spec or you find a gap we missed within a year, we come back and fix it free.

DIY or Call Us?

There are a few things you can do yourself safely. Check your current insulation depth with a ruler. Look for water stains, dark spots, or rodent activity. Confirm your bathroom vents terminate through the roof, not into the attic. Those checks take twenty minutes and they’ll tell you a lot.

Where DIY goes wrong is when someone buys a few bags of blown-in from the big box store, rents the machine, and starts spraying without sealing air leaks first. In Austin, that’s a recipe for hot, humid air pulling through every ceiling penetration and condensing against your new insulation. We routinely fix DIY blow-ins where the homeowner didn’t air seal first and now has damp, matted insulation six months later. Fiberglass itself is an irritant but proper gloves and an N95 mask make handling batts manageable. Removing old insulation, dealing with rodent droppings, and air sealing around live electrical penetrations is a different job entirely. If any of that sounds like more than you want to tackle on a Saturday in a hot attic, call us at (325) 246-2929 and we’ll handle it.

FAQs